STEAL SHIELD SS-300H INSTRUCTION MANUAL
SECTION 2: SYSTEM OPERATION
2.1 Alarm
On/Arm
1. Press and release
the transmitter button #1 after you exit the vehicle.
2. One-chirp sounds
and a parking light flash will verify alarm on.
3. Doors will lock
(If optional keyless entry has been installed).
4. Visible theft
warning LED light will flash slowly.
NOTE: If you hear four
chirp sounds, the system has detected an open door condition or faulty sensor.
If faulty sensor or faulty door pin is detected, the system will ignore these
zones until restored (Zone bypass).
AUTO
RE-ARM:
SS-300H model has
Auto Re-arm feature. Auto Re-arm feature will arm the unit if a door is not
opened within 20 seconds of disarm operation.
PASSIVE
MODE:
If the system is in
Passive Mode (Automatic Arming Mode),
1. Close the door.
There will be a 20 second arming delay. (If interior light is connected or has
a factory delayed interior light, arming will start after interior light has
turned off.)
2. The LED will flash
rapidly during a 20 second arming delay. At any time during a 20 second arming
delay, you can always press and release transmitter button #1 to arm manually.
3. After a 20 second
arming delay, alarm will arm automatically.
4. One-chirp
sound and a parking light flash will verify this operation.
5. Doors lock.
6. Visible theft
warning LED light will flash slowly.
2.2 Alarm
Off/Disarm
1. Press and release
the transmitter button #1 before entering the vehicle.
2. Two chirp sounds
and two parking light flashes will verify alarm off.
3. Doors will unlock
(If optional keyless entry has been installed).
4. The LED theft
warning light will stop flashing.
5. Interior Light
will turn on for 30 seconds. (If installed)
6. The LED is active
as test signal for sensors.
Note: If you hear three
chirp sounds, the system has been triggered and the alarm was activated while
you were away from the vehicle. Please refer to following chart. This
diagnostic report will turn off when the ignition switch is turned on.
|
Diagnostic Report |
Audible - Chirp |
Visual – LED |
|
Shock Sensor or
other input sensors |
3 chirps |
Double Flashes |
|
Door, Hood, Trunk,
or Voltage Drop Violation |
3 chirps |
Rapid Flashes |
2.3
Personal Protection Alarm (Panic Alarm)
1. Press and hold the
transmitter button #1 for approximately three seconds.
2. Personal Panic
alarm will be activated and siren will sound and parking lights will flash for
three minutes. Then shuts off automatically.
3. Press and release
the transmitter button #1 to cancel the panic alarm.
2.4 Trunk
Release Option
1. Press and hold the
transmitter button #2 for approximately two seconds.
2. Two chirp sounds
and two parking light flashes will verify the trunk release operation.
3. Trunk release
solenoid will unlatch the trunk automatically. Alarm will disarm at the
same time.
2.5 Emergency Key Disarm (If you lost your remote and can not start your vehicle or turn off the alarm)
To turn off the
system without your remote control,
1.With your vehicle key in the key cylinder, turn
it on. (On means driving position.)
2. Press and release
the valet switch 4 times.
3. The system will
disarm immediately.
Note: In passive mode, if
an Emergency Key Disarm was used to disarm the system, 10 seconds entry delay
feature engages automatically to give you sufficient time to use Emergency Key
Disarm procedure to disarm (turn off) the system without triggering the alarm.
This feature turns off automatically when the transmitter is used.
2.6 Valet
Mode (Keyless Entry Mode)
To turn off all
security features and use the system as keyless entry,
1. With your vehicle
key in the key cylinder, turn it on. (On means driving
position.)
2. Press and hold the
valet switch for 5 seconds.
3. One chirp sound
and a light flash will verify the Valet Mode.
4. The LED will flash
short-long flashes.
5. To exit from the
Valet Mode, repeat step 1 to 3. Two quick chirp sounds and two parking light
flashes will verify the operation.
3.1
Permanent Reprogramable Factory Code (Code
Pre-Programmed By Factory)
When the Dealer
installs the unit he programs your unique code, which is in permanent memory.
Any Authorized Dealer can add a new or an additional pre-coded transmitter and
delete an existing code from memory.
To program a new code
(This will delete all previous codes in the memory),
1. Turn the ignition
on then off 5 times. Then on 6th time turn the ignition on then leave
it on.
2. Within
10 seconds, press and release the button #1 of new transmitter.
3. If you have
additional remotes to program, press and release the button #1 of 2nd
transmitter. Press and release the button #1 of 3rd transmitter. Unit receives
up to 3 different transmitters.
4. Turn off the
ignition to exit code program mode.
Note: Module will accept
(3) three different transmitters.
3.2 One
Time Soft Chirp
Arm/Disarm chirp can
be temporarily softened from your remote transmitter.
To use one time soft
chirp,
1. Press and release
the transmitter button #2.
2. Press and release
the transmitter button #1 or #2 for desired function.
Example: To arm the system
with soft chirp sound, press and release the transmitter button #2 first. Then
press and release the transmitter button #1.
3.3 Permanent Siren Chirp Enable/Disable (Factory default setting: Chirp Enable)
Arm/Disarm chirp can
be permanently enabled and disabled from your remote transmitter.
For PERMANENT SIREN
CHIRP DISABLE or ENABLE,
1. Turn the ignition
on. Ignition on means normal driving position
2. Press and hold the
transmitter button #2 for 5 seconds.
3. SIREN CHIRP
DISABLE is confirmed with one siren chirp sound and one parking light flash.
SIREN CHIRP ENABLE is
confirmed with two siren chirp sounds and two parking light flashes.
Factory Default
Setting in Bold Letter
|
Programming
Function |
Programming
Method |
Chirp |
Light |
|
Passive
Mode with Passive Lock Active
Mode (4.1) |
With
the ignition on, press and release the transmitter button #1, #2, #1, #2 in
succession. |
1 2 |
1 2 |
|
Drive
Lock ON Drive
Lock OFF (4.2) |
With
the ignition on, press and release the transmitter button #1, #3, #1, #3 in
succession. |
1 2 |
1 2 |
|
Last
Door Closed Arming Off Last
Door Closed Arming On (4.4) |
With
the ignition on, press and release the transmitter button #1, #2, #1, #3 in
succession. |
1 2 |
1 2 |
|
Reset
to Factory Default (4.6) |
With
the ignition on, press and hold the LED/VS switch for 15 seconds. |
3
|
3 |
4.1 Passive/Active Mode (Factory Default Setting: Active Mode)
Passive arming with
passive lock mode means that the system will automatically arm and lock the
doors 20 seconds after the ignition key is turned off and the last door of the
vehicle is closed (If last door closed arming is enabled - See 4.4.
Otherwise, 20 seconds
after the ignition key is turned off). Sometimes referred to a
Automatic Arming.
Active arming mode
means that the system will not arm until you manually turn it on by pressing
the arming button on your radio frequency transmitter. Sometimes
referred to as Manual Arming.
For PASSIVE or ACTIVE
MODE,
1. Turn the ignition
on. Ignition on means normal driving position.
2. Within
10 seconds, press and release the transmitter button #1, #2, #1, #2 in
succession.
3. PASSIVE MODE is
confirmed with one siren chirp sound and one parking light flash.
ACTIVE MODE is
confirmed with two siren chirp sounds and two parking light flashes.
CAUTION: If
the automatic door lock feature is installed and the system is programmed to
passive mode the doors will lock automatically when the system arms. It is
always advisable to remove the ignition key each time you exit the vehicle.
4.2 Drive Lock Mode (Factory Default Setting: Drive Lock Off)
Drive Lock Mode means
that all doors will lock automatically two (2) seconds after the ignition key
is turned on and will unlock automatically when the ignition key is turned off.
This assumes that your Dealer has installed the keyless entry option, sometimes
referred to as Ignition Lock.
For drive lock mode
change,
1. Turn the ignition
on. Ignition on means normal driving position.
2. Within
10 seconds, press and release the transmitter button #1, #3, #1, #3 in
succession.
3. DRIVE LOCK MODE ON
is confirmed with one siren chirp sound & one parking light flash.
DRIVE LOCK MODE OFF
is confirmed with two siren chirp sounds & two parking light flashes.
4.4 Last
Door Closed Arming On/Off (Factory Default: Last Door Closed Arming On)
Last door close auto arming means that when you turn the Ignition off, close the last door it will automatically arm the system, also will lock the doors.
For LAST DOOR CLOSED
ARMING ON or LAST DOOR CLOSED ARMING OFF,
1. Turn the ignition
on. Ignition on means normal driving position.
2. Within
10 seconds, press and release the transmitter button #1, #2, #1, #3 in
succession.
3. LDCA OFF is
confirmed with one siren chirp sound and one parking light flash.
LDCA ON is confirmed
with two siren chirp sounds and two parking light flashes
WARNING: If LAST DOOR CLOSED ARMING ON failing to remove the keys from the key cylinder after switching the ignition off, will lock your vehicle.
4.6 Reset
to Factory Default
To reset all
programmable features to factory default setting:
1. Turn the ignition
on. Ignition on means normal driving position.
2. Within
10 seconds, press and hold the LED/VS switch for 15 seconds.
3. Reset to factory
default is confirmed with three siren chirp sounds and three parking light
flashes.
Recommended Battery:
12V - 23A
1. Remove the screw
from the back of the transmitter.
2. Remove front
cover, remove old battery carefully.
3. Replace with fresh
new battery and close front cover.
4. Press any button,
check for light flash from LED. (If no LED flash, change polarity of battery)
NOTE: Normal battery life
is approximately two years, but varies depending on usage. For optimum
performance and RF range, replace the battery at least once a year.
6.1 Limited 12 Month Warranty
SS300H unit and their accessories are warranted to be
free of defect in materials and workmanship.
In case of the products failure under a normal use situation within 12
months from the date of Purchase/Installation, please return the defective unit
to the dealer for repairing on a free-of-charge basis. However, customers might be charged for the
cost of spare parts if the malfunction of system is resulted from the
customer's carelessness or improper use of the product. This warranty does not
include accessories externally installed..
Please be noted that the followings are not covered by
warranty
Ø
If the siren horn is getting wet due to body damage of the vehicle or
misuse.
Ø
Batteries, including those for the remote controller and the main unit.
Ø
The main unit is not operational due to customer’s repairing or
replacement of parts by their own means or due to the fact that the unit has
got wet or is burned by improper wiring.
Ø
Central locking motors, boot release actuators, engine immobiliser
relays, etc.
6.2 Service and Maintenance
For more
information and technical support, contact your dealer or installer with proof
of purchase.
http://www.stealshield.com